# 1
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I bought this bike rack because I didn't want to have to remove my bed cover every time I wanted to take our bikes on a trip. This rack works perfect because I can roll up my cover and this thing just clamps across the bed. Taking the front tire on and off is kind of time consuming but when I travel with my brother who has a hitch mount rack, it takes him just as long to unload his bike as it takes me to unload. The wheel mounts tighten easily and the bikes appear secure during long drives, so I don't worry about them coming loose. Of course, you'll want to wrap a bike chain around the bike and rack if you plan to leave them out to make sure no one can steal the bike (although it would be missing a wheel)
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
# 2
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
So far so good. It is exactly what I thought it would be... So far no surprises. I received it and had it installed within 15 minutes. It's installed on the front of a Ford E350 van which is built out as a Coleman RV. I was worried about clearances but as the pictures show that is not a problem at all.
# 3
Swagman Patrol Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer and 15-mm Thru-Axle
The quality of the rack is fantastic. Sadly the keys do not work on the Locking Quick Release Skewers. I've contacted Swagman about this and am waiting for a response.
rack tends to work itself loose from bed walls during long trips. had to strap down with ratchet straps to keep from moving. locks only work at a specific angle -- wish the manual had said this because we couldn't lock our bikes until figuring it out.
# 4
Softride Shuttle Pad Tailgate Pad for Mid-Size Trucks - Up to 6 Bikes - 54" Wide
Order process was easy & information was great. The order processed quickly & came on time. It looks & works greats. It was easy to put on & took only a few minutes to install. I have 2 expensive bikes & one is an extra large frame. It fits great. The only thing I had to add when transporting was a strap around the tires on my tailgate as a precaution & to prevent any movement. It would be fine without it & the product works exactly as I expected. I put in on a 2000 Toyota Tundra. Very Happy! Exactly what I have been looking for & the price was just right. Thank You!!!
Received this tailgate cover very promptly, two days ahead of scheduled delivery date, and just in time to use yesterday. Cover was dry easy to install ( no directions required) and fit my tailgate well. I particularly liked the included Velcro tie downs and access pocket, which allows you to utilize your tailgate release. As you can see from the attached photo, it easily accommodated 4 additional bikes w/ front wheels still attached, and allowed me to transport 7 total bikes of varying design. Our 4 hr drive showed no indication of movement and the cover stayed in place securely. Great product!
# 5
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I own a 2005 Jeep Wrangler X with 31x10.5x15 oversized tires and wheels. I installed B6196001 HighRock 4x4 Oversize Tire Carrier by Bestop to carry larger spare tire. I needed a bike carrier that would carry our two crusier bikes and clear my spare tire. After measuring, I ordered: -> S64650 - Swagman 2-bike carrier -> 80300 - 7" Hitch Adapter 2" to 1-1/4" Trailer Hitch Receiver -> RM-061 - Roadmaster Quiet Hitch for 2" Trailer Hitches Our order arrived very quickly, etrailer.com upgraded the shipping. All these products arrived well packaged and without damage. In 15 minutes I had every thing assembled, installed on my Jeep and bikes loaded. The bike carrier is very well constructed, finish is excellent and easy to adjust. When adjusting wheel loops and loading bikes, make sure you pay attention to bike pedal position. I chose this extension because I did not want to use the adapter that comes with the bike carrier, I wanted as few parts as possible to keep rattles to a minimum and gives me more options for towing. The anti-rattle bolt/pin firmly secures the bike carrier to the extension and the Roadmaster Quiet Hitch keeps the extension adapter from rattling in the receiver. Road tested approximately 25 miles over rough city roads ( including railroad tracks ), county roads and highway. Bikes traveled very well without any rattles. I can remove my complete setup quickly, fold and put in rear of Jeep if desired. I am very well pleased with my purchase. Note to etrailer: Please consider offering Roadmaster Quiet Hitch in black to match receiver and accessories. Paul In the Land of Oz . . . Just South of the Yellow Brick Road!
It works great! Easy, quick, you know. One needs to screw in the hitch bolt, for some reason, before latching it. Other than that, it makes going bike riding way easier.
# 6
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
Super sturdy and easy to use/install. Love the bolt hitch attachment, keeps the rack from swaying/wobbling. Attachment points are very solid and the anti swing clips keep your bikes from smashing into each other and the rack during fast starts and stops. I use for all types of bikes, road, mountain, cruiser, children's, etc.
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
# 7
Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On
The Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On, is just what I was looking for to be able to build a bike rack for carrying one of my bikes on my motorcycle. It was easy to mount and it holds my bike in place while riding on bumpy dirt roads, city streets, highways and even when I hit some twisty country roads. It's really easy to load and unload my bike when I get to where I want to ride. I use a velcro strap around the quick-release and the fork arm as an added safety as well as a couple tie-downs from my bike handlebars to my motorcycle passenger pegs to help distribute the weight on my rack. If you want to build your own DIY bike rack I totally recommend the Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On.
Love this product! I built a great bike carrying system for my F-150 using two of these fork clamps. They are easy to install and extremely well made. No more tangled bikes and lots more room in the bed for other stuff! Best way to go for a nice bike rack system. Thanks, Phil T.
# 8
Swagman XTC4 Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
Rack is very sturdy and heavy duty. Instructions were terrible. Locking hitch pin would not thread correctly and ended up damaging it. Thankfully the threads on rack were fine and I was able to use the non-locking threaded pin. Would like a replacement locking pin ASAP
If you've done any research or read any of the other comments on either this rack, or this seller...rest assured they really are as good as everyone says! I ordered my rack on around 4pm est on a Friday afternoon and within an hour I received an email that said they have shipped my product AND upgraded to priority shipping. Can't say enough positive things about the customer service! When the rack arrived, it took me a little over half an hour to get it set up. Probably would e been faster if I were even slightly mechanically inclined (or if didn't I didn't have to borrow a socket wrench from my neighbor). We finally had an opportunity to load up the bikes and head out for a ride today. As others have said, the first time you load up your bikes, it's kind of like a puzzle to get them situated. Took about 15 minutes. This rack is awesome! Very sturdy and the bikes were very secure. Only racks I have had in the past were rooftop fork mount racks. This is so much easier! On e we got to the trail (over an hour drive) getting the bikes off was a piece of cake. Afterwards, it was time to load them back up and it was less than 5 minutes to get them all on and ready to hit the road. There were other 4-bike racks on the website, but this one had enough great reviews that I felt comfortable making the purchase. After the fact, I'm very glad I did! I can't imagine the $800 rack can be that much better than this, and I highly recommend this for anyone looking for a 4-bike platform rack. I will definitely recommend this rack and etrailer.com to everyone I know.
# 9
Swagman Chinook Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
Truly grooving on my wife's new Swagman Chinook bike rack. She wanted to be able to transport her nice road bike easily without throwing it in the back of her car, and since a roof rack is out of the question, this Swagman model fit the bill perfectly. It arrived quickly on the anticipated date. Kudos to etrailer.com for the email updates to keep me informed of my purchase. Within one hour, it was installed on my wife's 2014 Mazda3 hatchback. The Swagman is heavy and solid, which is reassuring as it makes me feel confident that it will keep the bikes secure. It also makes me feel like I got my money's worth. A ratchet wrench and Phillip's head screwdriver were the only tools required for the easy install. I did my research before purchasing the Chinook model as I was also eyeballing a very similar Thule rack that was slightly more expensive. I spoke with an etrailer.com expert who gave me the lowdown on both models. Ultimately, the Swagman won out because it has a smaller 'footprint' while extended or folded up ... and also can tilt away from the car for easy access to the hatchback area. Very convenient! FYI: Mazda doesn't make a trailer hitch for the Mazda3 as it's a small car with a small engine and has no business towing anything. Thankfully, the Curt company makes an aftermarket frame and trailer hitch that fits the Mazda3 hatchback perfectly with no drilling. Stupidly, I purchased it from another online company thinking I was getting a good deal. Turns out etrailer.com had it for less with FREE shipping. Oh well ... live and learn. Now I know that etrailer.com is one-stop shopping for bike racks AND trailer hitches. (Full disclosure: I had the garage down the street install the frame as it's easier with a lift) Only snafu: the shipment contained an extra set of keys that I assumed was for the hitch bolt lock (there was also a set of keys on the bolt itself). I spent 15 minutes using those keys trying to figure out how to remove the lock from the bolt to install it on the hitch. The keys just wouldn't turn in the lock. I called etrailer.com and Kevin told me to try the other set of keys ... and they worked. So an extra set of keys came with it that did absolutely nothing ... weird! Obviously, I can't speak to the longevity and durability of the Swagman Chinook 2 Bike Platform Rack as I just installed it. What I can speak to is the sturdiness of it, the ease of the installation and my complete satisfaction with the good folks at etrailer.com.
I ordered the Swagman Chinook 2 Bike Platform Rack on line from etrailer and so far have been very satisfied. The bike rack was delivered in less than a week. Unpacking the rack and assembly was fairly straightforward. I have read some reviews that complained the assembly instructions were a bit vague. I didn't have a problem but can see where others without a mechanical background get confused. The rack is very sturdy, but there is some side to side play in the tilt mechanism. I'm not sure this can be avoided with a rack that folds down. Installing the Curt trunk stabilizing strap takes most of the sway out of the rack. Installation is fairly easy and quick. It takes me 6 - 7 minutes to install the back on my hitch, and to install the bike and be ready to drive away. That seems reasonable to me. So far I've only loaded 1 bike. I've included pictures of my installation on a 2014 Mercedes Benz E350 sedan. Clearance between the bikes, the rack and the car are good. With the bike loaded in the inside, most forward position, I have 6" clearance between the pedal and the bumper. With the bike removed, the center support folded flat and the rack folded up in the storage position, I have 4" clearance between the closest part of the bike rack (the fold down hinge assembly) and the back bumper of the car. I am able to open the trunk of the car without removing the bikes or using the tilt feature, but I do have to remove the stabilizing strap first. Overall, I'm very pleased with the bike rack and think it will serve me much better than my old strap on rack. Since the weather has been cool since getting the bike carrier, I haven't taken any long trips to give it a real workout.
# 10
Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Pearl
No buyer’s remorse here! After quite a bit of reading and comparing, I have no regrets about purchasing the Kuat Sherpa 2.0. Excellent product, great quality. I would purchase all over again. It is a solid rack that is esthetically impressive to boot.
I love this bike rack. I feel that my bikes are secure and it fits my road and mountain bikes. Also, I love the Pearl color as it matches my car.
# 11
Thule GateMate Pro Tailgate Pad for Full-Size Trucks - Up to 7 Bikes - 53" Wide
It has 7 different areas to strap bicycles down but there is definitely not room to strap 7 bikes down from what I can tell. The straps were a little tricky to feed under the tailgate and pull up at the same time with only one person. Overall it works pretty well but it appears to only have enough room for 4 MTN bikes.
Very sturdy and well made. Great for a barrier between bikes and tailgate so it is not scratched. The camera flap is a plus so the rear view camera is accessible. No issues a year after purchase. Fits a 2014 Chevy Silverado 1500 and 2022 RAM 2500 equally well.
# 12
SportRack Ridge Bike Rack for 4 Bikes - 2" Hitches - Swing Away
Unit doesn't fit a Jeep Rubicon with a spare tire. I tried 4 times and contacted etrailer.com that the unit doesn't work as sold and they offered to sell me a 7 3/4 extension and reduce the load capacity 50%. The length of the 2" hitch needs to be 3" longer for a standard Rubicon to get past the spare. You not going to want to take your spare tire off for the hitch to work. It defeats the purpose. Customer service was excellent, however the product is a flawed design. Can't recommend this hitch. Its also heavy.
Solid rack for half the price of the name brands. Don’t waste your money! Thanks to the extensive reviews on etrailer and a free shipping promotion I took a chance and ordered this along with the three of their crossbars, anti rattle hitch pin and cable lock. All for well less than the name brand rack alone. Shipping was painful. Etrailer said it was in stock but then due to a delay with the manufacturer it took 35 days from order to arrival. I wasn’t in a hurry so I waited patiently, and etrailer reps emailed often to lmk they hadn’t forgotten. I thought some kind of reward for my extreme patience was in order- discount, gift card, free bag of chips- but they politely declined. Oh well. In the end it arrived when they (eventually) said it would, all in one box, in great shape. The rack was super easy to assemble. You’ll need a ratchet or two and you’ll need to crank those bolts to assemble- they don’t just “insert.” But otherwise it’s only a few steps; I had mine hanging on my truck in probably 15 minutes. Swings away and locks smoothly and requires no effort to do so. Everything feels quite sturdy and well made. No rattle on initial test drive either. This will be a once in a while rack at best for our family of four. We have two SUVs so I needed a rack that could get out of the way of the rear hatch WITH bikes on it. This will do that. And now I don’t need to stuff four dirty bikes into the back of my truck, getting them all tangled and scratched!
# 13
Rhino-Rack Road Warrior Rooftop Bike Carrier - Fork Mount
This bike carrier has a clean design and it assembled and attached to the roof rack easily. A locking front cover prevents it from being detached from the roof rack and the tray has a cut out in the front for a disc brake if my next bike has one. Once everything is snug, the bike feels solid and there's no slop.
I'm not too sure how to rate this but I'm not happy with it. Everything that happened is no fault of etrailer. I've made many purchases from etrailer, they're a great distributor. The bike rack appears to be great. The problem seems to be that they changed the design. To start, UPS damaged the box in shipping and then tried to tape the package they sent me. After walking through the parts in the box with an etrailer rep on the phone, it seemed that no parts were missing. So I proceeded to connect everything up based on the instructions. As I put it together I noticed the mounting bracket in the rear doesn't have anything to remove the slop. The rear is literally resting on a slider, which means that it would rattle when driving around. Just for kicks I took it for a drive with my bike on top. It rattled like crazy! So I looked at the installation videos on etrailer and then youtube. Every one of them showed an extra rear mounting bracket with knobs to tighten. These were not listed in the install manual so I suspect Rhino thought they could cut cost by eliminating them. I contacted etrailer to see if they had any. They didn't. So I returned it. Sadly, I still had to pay a $25 restocking fee. I'm not sure why etrailer charged me. It's not like I bought the wrong thing and didn't want it. It's actually a really nice bike carrier. Just a flaw in the design that etrailer should catch when they test it out in their videos. If anything, I've helped them out with this. Hopefully etrailer will test out what I sent them, then reach out to Rhino about this new design flaw. Again, I like etrailer as a service but I wish they had caught this before selling to me (and others). I strongly suggest that you don't buy this until the bracket issue gets resolved. Also, take a look at the last pic of the Inno XA391 on the etrailer site. They resolve the rear bracket rattle by putting in a thumb screw.
# 14
Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount
The BEST bike carrier by far!! We are both in our 7th decade and even I alone (5’2” 120 lbs) can manage to attach this in my hitch without any issues. It’s so easy to load both our hybrid and e-bike and they are super secure. We love that it folds up small and wheels away when not in use. This bike carrier is worth every penny!!
This rack is perfect! eTrailer had it shipped and at my home in almost no time. I drove with it on the car today, and it was solid and secure. It's super easy to get on and off the hitch. I'm 5'1 and I was able to load the bike on with the ramp without a struggle. Thanks for the thorough video and comparison information. It made this purchase easy.
# 15
Hollywood Racks Trail Rider Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
I love this bike rack. It was easy to install, has zero problems/issues and my bike was always secure and safe. I did add a cable and lock to act as a theft deterrent while paying for gas, etc. The price is very reasonable compared to others in the market and e-trailers made every step of the purchase and install easy and as simple as one could hope for.
I was impressed with this bike rack from the minute I unpacked it. The assembly was simple & straight forward. I looked at quite a few bike racks & for the price point this product was hard to beat. It is well designed & the keyhole pins make it easy to remove & fold up when not carrying the bikes. The locking hitch pin & locking frame bars are convenient and fairly secure. I will add my cable lock to make the bikes even a little more tamper proof. So far I’m very happy with this his purchase. Now the test of time!
# 16
Saris Traps Fork-Block 3 Bike Rack - Single Track - 47" Long - 9-mm Skewer
This works perfectly in my 2007 Nissan Quest minivan. I am able to securely and rapidly store and transport 3 bikes wile keeping 3 seats usable in the van. The base is heavy enough that it stays put so that the bikes stay still and do not knock into each other on the trip. I *might* be able to fit 4 bikes in there, but only if I put down another seat, leaving room for only 2 passengers, so I'll say 3 bikes and 3 people in my minivan is the sweet spot for this. It really is nice that I can load them so rapidly and that the bikes do not have to touch each other.
Thanks for the follow up emails. Received my interior saris fork mount carrier and already have people raving about it. Here is a photo for subaru outback 2014 with saris Thanks again
Yakima GateKeeper Tailgate Pad Review - 2023 Chevrolet Colorado
Hi. Matt with etrailer. Today we're gonna talk about the Yakima Tailgate Pad on the back of the 2023 Chevrolet Colorado. Now, this is gonna be a great option for you if you want something at that entry level price and something that's gonna be able to organize and keep your bikes secured on the back of your Colorado. Now, it's also gonna be a great option for you if you don't wanna invest in getting a hitch, or you wanna use your hitch for something else and you don't wanna get that bike rack too. It's gonna be really easy to use.
Yakima GateKeeper Tailgate Pad Review - 2022 Chevrolet Colorado
How's it going neighbors This is Ed here with etrailer.com, and we're taking a look at the Yakima Gatekeeper, on the back of a 2022 Chevrolet Colorado. Let's check it out. So the Gatekeeper is gonna be a five bike carrier, having the five cradles that you're gonna strap your bike down to, to keep it in position. So, officially, what you're gonna do, to attach your bike, you're gonna hook that one end of your cradle to the other, and this is all padded, and then you'll be able to make your adjustment, as far as how tight you would like it to stabilize your bike, using your strap. If you have a bike that you wouldn't wanna make contact with your frame, it definitely wouldn't be the best option. However, it's a really good option, as far as moving multiple bikes, using your pickup without a hitch carrier.
Kuat Huk Half Truck Tailgate Pad Review - 2022 Chevrolet Colorado
How's it going, neighbors This is Ed here. Taking a look at the Huk half size two bike pad on the back of our 2022 Chevrolet Colorado. You secure your bike to the Huk using the straps that are provided. And you just thread it through one of the four loops here on the carrier. The whole carrier, it's padded. It's scratch resistant lining to go against the finish of your vehicle.
Kuat Hitch Bike Racks Review - 2021 Chevrolet Colorado
Hi there Colorado owners, today, on our 2021 Chevrolet Colorado. We're going to be test-fitting Cuats NB 2.0 platform bike rack. It's available in either black or gray like we're showing off today. And also in a four or a two bike rack version. This is a premium platform rack that will allow you to bring two or four bikes with you. We can see here that it secures our bike and it secures it very well because it secures it with a cradle here on the front wheel.
Kuat Hitch Bike Racks Review - 2020 Chevrolet Colorado
Hey, everybody. Welcome to etrailer.com. I'm Bobby, and today we're taking a look at the Kuat NV 2.0 on our 2020, Chevy Colorado. Now this is gonna be a nice stylish way of getting our bikes on the trail with us. As you can see, pretty much top of the line model as my opinions are, very sleek design and it's gonna be nice and durable and it's been tested by a lot of people. So we know it's gonna hold up quite well for us.
Yakima Hitch Bike Racks Review - 2020 Chevrolet Colorado
Hey, everybody. Welcome to etrailer.com. I'm Bobby. And today we're taking a look at the Yakima Backroad 4 bike rack on our 2020 Chevy Colorado. Now this can be a great way of getting you and some of your friends, maybe your family on the road with you and getting the bikes to the trail in a pretty efficient way. Today look, we can see it's a hanging style rack.
Kuat Hitch Bike Racks Review - 2020 Chevrolet Colorado sh22g
Hey everybody, welcome to etrailer.com. I'm Bobby, and today we're taking a look at the Kuat Sherpa 2.0 bike rack for two bikes on our 2020 Chevy Colorado. Now as you can see, it's gonna be a nice stylish way of getting our bikes on the road with us, and we're also getting a platform style, and we are also getting a wheel hold mount here. So if you're looking a way of getting those carbon frame bikes on the road with you, this is gonna be a great option, as we aren't getting any frame contact so we won't be damaging that carbon frame at all. Definitely be a great way of getting those carbon frames. However, this also makes it pretty adaptive to most bikes that you want to get on here.
Inno Hitch Bike Racks Review - 2020 Chevrolet Colorado
Hey guys, welcome to etrailer.com. I'm Bobby and today we're taking a look at the Inno Tire Hold 2 Bike Platform Rack on our 2020 Chevy Colorado. Now, as you can see, it's gonna be a great way of getting those two bikes on the trail with us and you can see we're getting a nice long platform on here. So if you're looking for a way of getting some of those longer bikes on here this is gonna be a great option for you. As you see, we have our carbon frame up on here today. The reason we can do that as the name suggests we are holding onto both of our tires on this Inno Tire Hold and why that can be great, A, as you can see we are getting this carbon frames up on here.
Hollywood Racks Hitch Bike Racks Review - 2020 Chevrolet Colorado hly94fr
Hey, everybody. Welcome to etrailer.com. I'm Bobby. And today we're taking a look at the Hollywood racks destination two bike platform rack on our 2020 Chevy Colorado. Now, as you can see, it's going to be a pretty nice way of getting our bikes to the trail with us today. And as you can see we are having a style of a platform here.
Thule Hitching Post Pro Hitch Bike Racks Review - 2019 Chevrolet Colorado
Collin: Hey everyone. It's Collin here etrailer. And today, we have a 2019 Chevrolet Colorado. We're going to do a test of the Thule Hitching Post Pro. This is a four bike hanging style rack, so you're going to be able to get four bikes loaded up so you can haul them to and from your destination. What's really nice about the bike rack is that usually with these Colorado's, they do have smaller beds than a full size pickup, so you're going to be able to get all your cargo and other gear inside your truck bed while getting your bikes loaded on the outside.
Hollywood Racks Hitch Bike Racks Review - 2019 Chevrolet Colorado
Today in our 2019 Chevrolet Colorado, we're gonna be doing a test fit on the Hollywood Racks Sport Rider SE four bike platform rack. Part number HR1400Z. Now a couple of features I want to show right off the bat is one, this two bike extension can be removed if you only want to take two bikes out. All you have to do is loosen up this anti rattle handle right here and that will loosen up this pin that you can take out and then pull the two bike extension off and that's gonna shorten the length added onto the back of your vehicle and take some of the weight off if you're only gonna take two bikes out.The other feature I want to show is that it can tilt away from the vehicle. We're just gonna come in here and remove this snapper pin. It might help to pick up on the back of the bike rack and then we're gonna pull that pin and let it tilt away.
Hollywood Racks Hitch Bike Racks Review - 2019 Chevrolet Colorado HR1450Z-FB
Today, on our 2019 Chevrolet Colorado, we're gonna be doing a test fit on the Hollywood Racks Sport Rider SE2 2-bike platform rack for fat bikes. Part number HR1450Z-FB. This 2-bike carrier comes with four cradles that'll fit your fat tire bikes up to 5" wide. You can see we have two different cradles on, so in addition to the four cradles you receive for your fat bike tires that are at 5" wide, you will get the regular cradles that will fit normal bike tires, up to 3" wide.The bike itself is held at three different points of connection. We have two hook and loop straps. One that's on the back wheel right here, and we also have another one that's on the front wheel.
Hollywood Racks Hitch Bike Racks Review - 2019 Chevrolet Colorado HR1450Z-85-FB
Today in our 2019 Chevrolet Colorado, we're gonna be doing a test fit on the Hollywood Racks Sport Rider SC 4-Bike Platform Rack for Fat Bikes, with a cargo carrier added on. Part number HR1450Z-85-FB.Now right away, one of the features that we're gonna point out is that this bike rack has a cargo carrier added on to the back of it to allow you to haul any gear you would like to outside of your vehicle.If you would wish, you can pull this cargo carrier out if you only wanna take your two bikes out, or you could even use this cargo carrier by itself in your two-inch hitch receiver.The weight capacity for a cargo carrier when it's added on is 90 pounds, but when you put it as a standalone carrier inside the hitch receiver, it's gonna be 200 pounds.Now on to the cradles of our bike rack. This bike rack's gonna give you four additional fat bike cradles that'll hold fat tire bikes up to five inches wide. You can see the comparison right here between the fat tire bike cradle and the standard cradle. You're also gonna have four of these standard cradles if you want to take out one fat tire bike and then one standard bike. For the standard bike tires, it's tires up to three inches wide.Now the bike rack has three different points where it's connected.
Hollywood Racks Hitch Bike Racks Review - 2019 Chevrolet Colorado HR1450Z-85
Today in our 2019 Chevrolet Colorado, we're gonna be doing a test fit on the Hollywood Racks Sport Rider SC 2-Bike Platform Rack with a cargo carrier attachment, part number HR1450Z-85.Now the addition that we'll point out right away is that we have a cargo carrier on the back of our bike rack, which isn't something you typically see a lot. With a cargo carrier attached to it, you're gonna be able to haul any of your biking equipment that you don't want inside of our vehicle, whether it's dirty or doesn't have the best smell to it.The weight capacity for the . when it's outside, on the end of it, is gonna be 90 pounds, but you could also remove it from the bike rack and use it as a standalone carrier, to which the weight limit will be 200 pounds. Or, if you just wanna take your two bikes out and you don't have any cargo to haul, you can also take it off and just use the bike rack.Now the bike itself is gonna be held in at three different points in contact. We have a hook-and-loop strap holding the back wheel in, and we have the same thing on the front. Those two straps are gonna make sure that the wheels stay in their trays and don't shift at all while we're traveling.
Hollywood Racks Hitch Bike Racks Review - 2019 Chevrolet Colorado HR1450Z
Today, on our 2019 Chevrolet Colorado, we're gonna be doing a test fit on the Hollywood Racks Sport Rider SE two-bike platform rack, part number HR1450Z. One of the cool features about this bike rack we'll start off with is that you can purchase add-ons for it whether you want to add on a two-by carrier to it or a cargo carrier to increased your hauling capacity. You can find those at etrailer.com.Another thing I want to point out is that we can tilt this away from our vehicle to gain better access to our truck bed. We'll remove that snapper pin first, and then we're gonna pull the pin on the other side and then let it tilt away, but you will find that when you open up your tailgate and you come down it is gonna make contact with the bike you have on there, but it does open up a good amount to where you can still hold it and get in to your track bed and grab any small thing you might need.To tilt it back up, just reverse the process. We'll tilt it back. It snapped into place, so we'll go ahead and replace this snapper pin.
RockyMounts Hitch Bike Racks Review - 2016 Chevrolet Colorado
Speaker 1: Today in our 2016 Chevrolet Colorado, we're going to be taking a look at the Rocky Mount's backstage two-bike platform rack. And that's going to be part number RKY-1002. As you can see, we have a bike installed, so let's take a closer look and show off some of the features.Now a great feature about this bike rack is that it can swing away from your vehicle to provide you with complete . bed access on our truck. How we're going to do that is we're going to start down here, we're going to loosen up this blue T-pin, and once that's all the way loose we can go ahead and come to this blue circular pin right here and pull up, and that's going to allow us to pull away our bike rack. You do want to make sure while you're doing this that you have a hold of the bike rack and not the bike itself.Next, we're going to tilt it this way just a bit like that, and then we're going to come to this pin right here that's at the corner of our two inaudible 00:01:09 frame bars.
Inno Hitch Bike Racks Review - 2016 Chevrolet Colorado
Speaker 1: Today in our 2016 Chevrolet Colorado, we're gonna be taking a look at the Inno Aero Lite 4 Bike Rack for 1 1/2" and 2" hitches. That's gonna be product number INH640. As you can see, we have a bike installed, so let's take a closer look and show off some of the features.Now, starting from the outside and working our way in, we're gonna have this integrated cable lock system which comes out from the base of our bike rack, wraps around our frames, and inserts into that slot right there. You will get a set of keys with your bike rack, so when you wanna remove the cable you simply just slide up this tab, you have the insert for your key to unlock your cable, and then unload your bikes.These cradles right here have a nice, thick rubber padding which is gonna help protect the frame of your bike from any type of scratches or abrasions during installation and travel. The cradles can also move back and forth, and slide up and down the rack to accommodate many different-sized bikes and any spacing between bikes that you might want.If we look at the bike itself, we're gonna see it's secured at three different points of contact. We have two straps on the top of our bike frame securing it into the cradles, then down here we're gonna have this anti-rattle cradle.
Yakima Hitch Bike Racks Review - 2015 Chevrolet Colorado
Hi everyone, Aiden here with etrailer. Today, we're taking a look at the Yakima StageTwo on our 2015 Chevrolet Colorado. Now, StageTwo is a platform style bike rack, and a really rugged one at that, it's gonna be really well built in heavy-duty. With this, we're holding the bike by our front tire, and it's not making any frame contact, so it's gonna be good for our carbon and alternative frame bikes, and it also has a 70 pound weight capacity per bike, which makes it good for some of our heavier e-bikes too. With this, you do have the ability to tilt it away with bikes loaded. Now, just come to the end of the handle here, squeeze it with both hands as you're applying a little bit of upward pressure, and then it will release, and that'll give us access to the bed of our truck with a full opening tailgate.
Saris Hitch Bike Racks Review - 2015 Chevrolet Colorado
Hi everyone, Aidan here with etrailer. Today we're taking a look at the Saris SuperClamp HD on our 2015 Chevrolet Colorado. The SuperClamp's a platform style bike rack, can hold up to 2 bikes and it's gonna hold them by the tires using these wheel hooks. Now this one's going to get an exceptionally strong hold on the bike. You can see there's no movement of the bike within the bike rack because we've got the hooks as well as cradles with straps on the bottom to keep everything really secure. A couple things to note here.
Saris Freedom Hitch Bike Racks Review - 2015 Chevrolet Colorado
Hi everyone. Aiden here with etrailer. Today we're taking a look at our Saris Freedom Bike Rack on our 2015 Chevrolet Colorado. Now the Freedom's gonna be a platform style bike rack holding the bike in these cradles, and by our frame it's gonna be a pretty entry level platform style rack but it does have some nice features that I really like compared to some other entry level options. The big thing of that being it's weight capacity it has a 60 pound capacity per bike which for an entry level rack is really uncommon. So if you need a way to carry e-bikes this is gonna be a nice way to do it at an affordable price point.
RockyMounts Hitch Bike Racks Review - 2015 Chevrolet Colorado
Hi everyone, Aiden here with etrailer. Today we're taking a look at the RockyMounts Guide Rail on our 2015 Chevrolet Colorado. The guide rail is a platform style bike rack, holding the bike with these wheel hoops. You've got one on each tire making for zero frame contact. That's gonna be a good fit for carbon frame and alternative frame bikes. And, for 60 pound weight capacity per bike, it can handle some e-bikes too.
RockyMounts Hitch Bike Racks Review - 2015 Chevrolet Colorado RKY10004
Hi everyone, Aiden here with etrailer. Today, we're taking a look at the RockyMounts MonoRail on our 2015 Chevrolet Colorado. It's gonna be a platform-style bike rack that's gonna hold the bike in the tray and by our front wheel. We're using a wheel hook to do that, and that's gonna mean zero frame contact, making it good for carbon frame and alternative frame bikes. With the 60 pound weight capacity per bike, it's gonna be able to handle some e-bikes too. It does hold the bike really well on there, there's really no movement of the bike within the bike rack itself, which is great to see, everything's stable.
Hollywood Racks Hitch Bike Racks Review - 2015 Chevrolet Colorado
Hi everyone. Aiden here with etrailer. Today we're taking a look at the Hollywood Racks Destination two bike rack on our 2015 Chevrolet Colorado. It's gonna be a more entry-level, platform-style bike rack. It's gonna hold the bike in these trays and primarily by our frame. We've got a cradle with a strap wrapped around the frame as well as two wheel straps at the bottom pulling the bike down and in.
Hollywood Racks Hitch Bike Racks Review - 2015 Chevrolet Colorado HLY66ZR
Hi, everyone. Aiden here with etrailer. Today we're taking a look at the Hollywood Racks Destination E-Bike on our 2015 Chevrolet Colorado. Now it's going to be an E-Bike rack that has a 70 pound weight capacity per bike, making it good for some of our heavier E-Bikes. With that, it is going to hold the bike in these trays, and by our frame up here. Frame contact does mean we wanna avoid carbon frame bikes, so it does eliminate that, but with the way the clamps rotate 360 degrees, and are able to move around, it should be good for alternative frame bikes, still.
CURT Hitch Bike Racks Review - 2015 Chevrolet Colorado
Hi, everyone. Aidan here with etrailer. Today, we're taking a look at the CURT Premium on our 2015 Chevrolet Colorado. The CURT Premium is a hanging style bike rack. It's gonna hold the bike up here by the frame and it's going to fall down right here. You've got two straps over top the frame to hold it in place as well as a third around the seatpost, limiting our side to side movement that will help with bike to bike contact.
What our customers are saying:
"I ordered a trailer hitch and a bike rack carrier the order was shipped with in three days. To put the hitch on only took about 30 mins. only had to drill two 1/2 holes. fit like a glove."